- UPGRADE INDUSTRIES XBEE SHEILD XBOARD SERIAL
- UPGRADE INDUSTRIES XBEE SHEILD XBOARD SOFTWARE
- UPGRADE INDUSTRIES XBEE SHEILD XBOARD CODE
- UPGRADE INDUSTRIES XBEE SHEILD XBOARD PC
License along with this library if not, write to the Free Softwareįoundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USAįor more details about the product please check You should have received a copy of the GNU Lesser General Public Lesser General Public License for more details. MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. This library is distributed in the hope that it will be useful,īut WITHOUT ANY WARRANTY without even the implied warranty of Version 2.1 of the License, or (at your option) any later version.
UPGRADE INDUSTRIES XBEE SHEILD XBOARD SOFTWARE
License as published by the Free Software Foundation either Modify it under the terms of the GNU Lesser General Public
UPGRADE INDUSTRIES XBEE SHEILD XBOARD CODE
This demo code is free software you can redistribute it and/or Bluetooth Bee is connected to Seeeduino via XBee®_Shield as shown above.īluetoothBee Demo Code - Flowcontrol Based ImplementationĢ010,2011 Copyright (c) Seeed Technology Inc.
UPGRADE INDUSTRIES XBEE SHEILD XBOARD PC
The following sketch configures Bluetooth Bee as Slave Device and waits for connection request from PC or other master device.
UPGRADE INDUSTRIES XBEE SHEILD XBOARD SERIAL
Upload this code to the Arudino hosting the Xbee Shield, startup the Serial Monitor and at that point the Arduino serial port will be connected via radio to any other xbee radios currently operating-anything you type in the serial monitor will be sent to the other radios and vise versa. Open serial communications and wait for port to open: SoftwareSerial mySerial(11, 12) // RX, TX The following code is taken almost directly from the Aruino SoftwareSerial manual.Įxample from Arduino SoftwareSerial tutorial The code above may have worked on earlier versions but the SoftwareSerial library is now part of the core.
The XBee should respond by sending back an "OK". Try sending "+++" (without the quotes) for XBee module, to the Arduino board. Serial.print((unsigned char)mySerial.read()) Īfter this fire up your favorite serial terminal software, choose the COM port for Arduino, set it to operate at default baud rate of your Bee (XBee default is 9600 8-N-1), connect and send the commands. MySerial.print((unsigned char)Serial.read()) Serial.begin(9600) // the terminal baud rate MySerial.begin(9600) // the Bee baud rate Bee Shield is connected to the Software UART serial link between the computer and the Bee Shield Xbee Shield Outline and Toggle Switch Position ¶Ĭreate a new sketch with the following code and download it into your Arduino board. Please refer the below tables for different configuration. Normally the Bee modules are connected via Software Serial Port by setting the toggle switches ( TOG_1 and TOG_2)positions to left-side. In case of a Seeeduino, set the operating voltage switch to 3.3V position.
Usage ¶Ī Bee module is connected to Arduino / Seeeduino via the XBee Shield. Set the toggle switches to correct position before connecting to Bee Modules or Arduinos.Connecting GPS Bee to Arduino / Seeeduino.Communicate Seeeduino / Arduino to PC Wirelessly using Bee Modules.Communicate two Seeeduinos / Arduinos Wirelessly using Bee Modules ( Xbee, BluetoothBee, RFBee).Xbee modules can be configured by X-CTU via USB To use X-CTU with Seeeduino, please upload following sketch void setup() Seeed Studio's XBee®_Shield is derived from Arduino Xbee shield, with following features: These two switches provides options to connect RxD and TxD lines of Bee Modules to Seeduino Hardware Serial Port or Digital pins 11 and 12 or FTDI RxD and Txd Pins. Two toggle switches decides how Rxd and Txd pins of Bee modules be connected to Seeeduino pins. ** It is used to connect two **Seeeduinos using Zigbee / Bluetooth Bee or connect a Seeeduino with PC Wirelessly. It can be used as a Serial Port / USB replacement. It is designed to be used with Xbee module from MaxStream. A Xbee shield allows an Arduino or Seeeduino board to communicate wirelessly using Bee compatible modules (like Zigbee or BlueTooth Bee).
0 kommentar(er)
